Product Specifications

Physical Size
Length: 74 in (188 cm)
Width: 34 in (86 cm)
Height: 53 in (135 cm)
Approximate Weight with Fluid: 2,500 lbs. (1134 kg)

Electric Motor
Motor Output: 50 hp (37 kw)
Motor Type: High Efficiency TEFC electric motor
Full load amps @ 460vac (60Hz): 58
Full load amps @ 230vac (60Hz): 116
Full load amps @ 380vac (50Hz): 71

Intensifier
Type: Single piston, dual plunger, reciprocating
Number of Intensifiers: one
Rate Pressure: 60,000 psi (4,100 bar)
Intensification Ratio: 20:1
Flow Rate: 1.1 gpm (5 lpm)
Maximum Rated Orifice Size .016 in (.41 mm)

Low-Pressure Water / Intensification Water
Type: Pretreated, <100 TDS, PH 6-8, Silica <15PPM
Supply Requirements: 1.0 gpm @ 20 psi (1.4 bar ) min. / 75°F (24°C) max.
Filtration: 1, .45 Micron

Coolant Water
Maximum Temperature: 70°F (21°C)
Minimum: 0-4.0 gpm (0-15.1 lpm) @ Minimum 20 psi (1.3 bar)
Ability to Remove: 39,000 BTUs /Hour

Hydraulics
Reservoir Capacity: 30 gallons (136.4 liters)
Filtration: 13 gpm (59.1 lpm) kidney loop @ 10 micron

Environmental
Ambient Room Temperature: 50°-100°F (10°-37°C)
Relative Humidity: Non-condensing, Maximum 95% @ 100°F

The Jet Edge iP60-50 is a 50-horsepower intensifier pump rated at 60,000 psi (4,100 bar). It is capable of producing output pressures from 1,000 to 55,000 psi (3,800 bar) with flow rates of 0 to 1.1 gallons (5 liters) per minute to a variety of cutting, surface-preparation or cleaning tools.

The iP60-50 features a TUV-certified attenuator that complies with ASME pressure vessel standards, to minimize pressure fluctuations.

The high-efficiency, totally enclosed, fan cooled (TEFC) electric motor with wye-delta "soft start" ensures high reliability, long service life and minimal energy usage. The motor drives an axial piston, variable displacement, pressure-compensated type hydraulic pump.

A programmable logic controller (PLC) monitors and controls all machine functions, and automatically energizes relays to light the warning lamps in the event of potentially damaging conditions.

Like all Jet Edge UHP intensifier pumps, the iP60-50 offers complete flexibility for waterjet cutting, cleaning or coating removal applications.

Design improvements:

Non-contact wet electronic stroke sensor improves performance and reliability
Redesigned intensifier assembly
Improved check tube
Extended-life hydraulic system
Easy access to components and minimal tools required for in-house servicing reduces downtime and improves productivity
Pistons can be changed in the field by users without any special tooling
No special torque wrenches required
Standard design Grade 8 fasteners are available through local sources or Jet Edge if required
High-pressure water and hydraulic end caps are solid stainless steel providing longer life and improving performance over plated model designs
Low pressure and high pressure tie rod design allows for specific torque values to be applied to the hydraulic and ultra-high pressure cylinders
Inlet water pressure requirements have been reduced to 30 PSI; booster pump is only required if customer's inlet water pressure is below 30 PSI

Construction
Heavy gauge sheet metal covers
Rugged all-steel welded framework
Hinged cover and removable access
panels for convenient machine
inspection and maintenance
Integral hydraulic reservoir
NEMA 12/13 rated electrical
enclosure

Standard Features
High efficiency TEFC motor
Electronically shifted intensifiers
Wye-Delta soft start with disconnect
0.5 gallon (1.9 liter) high pressure
attenuator with 1.45 micron filtration
Safety shutdown systems
Automatic safety pressure bleed-down
valve
Thermostatically controlled cooling
system
Dual pressure set points
Programmable Logic Controller (PLC)
for operation and safety monitoring
Axial piston, variable displacement,
pressure-compensated hydraulic pump
Liquid filled pressure gauges
UHP safety shielded tubing